RG 500 break in oil

Running in an engine is all about doing a certain amount of wear to the rings and cylinder bore surface. Unless some wear happens the rings may never seal properly.

When a Cylinder is bored and honed it finishes with many micro-ridges. They look like swirls going around the cylinder. After a while these ridges get smoothed off by the running action of the rings.  The key is getting the rings properly seated before the cylinder micro-ridges wear off.

Since synthetic oil virtually eliminates wear it is forbidden during break in. Using synthetic oil during break in of an old school cast iron cylinder (which Gammas have) will result in poor ring seating and reduced power until the next set of pistons is installed. Assuming the next set is run in with non- synthetic oil :-)

Go to a car parts store and get 2smoke oil for a lawn mower. Drain the oil tank and replace it all with lawn mower oil.  It's about 1500 cc of oil , so gets two bottles of lawn mower oil.

Gammas continue to run in the rings for about as long as it takes to go through an oil tank's worth of
Milage.

Engine Leak Detection

Athlete’s foot spray powder is very useful for leak detection.  It is sticky so it stays on the engine until hosed off.

Clean the engine.

Spray athlete’s foot powder all around the suspected leak source.

Start engine

Let engine warm up while bike remains stationary

Riding the bike will blow the leaky fluid all over the place which makes finding the source very difficult.

Eventually while the bike is running in place the leak will manifest itself.

Follow the leaking liquid trail up through the white athlete’s foot powder to the source.

Hose the powder off (It's easy and all of it flows off with a bit of water)

Fix the leak.

Tinactin powder spray is the best for leak detection.  It is the stickiest.  Make sure to the label specifies Tinactin _Powder_.

Lance Gamma Big Bore Motor - Take 2

Starts easier.  Less abrasive engine sound while putt-putting through town.  Pulls so hard up top I haven't found where the power tapers off yet.  I used to run my 500cc motor to redline all day long.  It's so intense with the Big Bore up there that I always upshift.

This is what I bought my Gamma for.  I wanted a big motor so it could ride through town discretely while also being able to scratch my speed itch out in the country.  Suzuki installed a crazy powerband for publicity purposes.  Lance Gamma has finally evolved the engine to what Suzuki should have released in the first place.

Rick has been telling me to try running a gear or two higher than usual.  When I do that the bike is buzzing less than I am used to at any given point in a corner.  Less buzz makes me more comfortable, which leads to carrying more speed.  Going faster makes my suspension work harder.  Going faster makes me have more speed entering the next straight.  Which means I have more speed when the next braking zone comes up more quickly than expected.

So what starts out being more comfortable winds up also being faster.  Who woulda thunk?

This engine will take a while for me to explore the limits of.  That's a good thing ;-)

Philosophy of engine building / RG500 Stator Installation

I have recently proved to myself once again that it is possible to work too fast building an engine.  

A mistake which would have taken another minute to carefully avoid during construction can turn into twenty hours of consternation and repair work later on.

OK, here's a recent war story from my RG500: I skipped looking in the manual at the stator mounting page.  Seemed fairly simple, just three screws after all.  Didn’t see the notice to use locktite.  Didn’t use locktite.

Turns out stators are under lots of periodic stress as the magnets in the rotor whirl around and electricity is generated.  Lack of locktite resulted in stator becoming loose.

Loose stator rattled around for a while.  Until a few windings wore through against the rotor and shorted out.  Causing one of the three yellow stator output wires to break and the stator to fry. 

Fifty twisty miles from home on the Coast Highway while zinging along in 6^th.  Sudden and complete spark disappearance.

Talk about a buzz kill.

---

Here's the fried stator:

---

Here's the RG500 Shop Manual item about installing the stator.  I don't know what Thread Lock 1342 is.  I used Red Locktite.  It's OK to use Red on small threads, it's only large things that need to be heated for disassembly.

---

Here's the loose screws.  Looks like they were rubbing against the inside of the rotor for a while.

---

It would have been a lot easier and less time consuming to have read the manual and used Locktite than to have to remove the stator again.  Here's a pic near the end of the job with the replacement stator in place:

---

It is important to pay attention to every word in a shop manual.  When they say "Route the stator lead wire properly" they mean it.  Suzuki cast a little post and threaded a mounting hole for a bracket just for this purpose.  After a previous rebuild I found out that if this bracket is left out the wire will rub the rotor, wear through, and cause the bike to stop running.

I made my own bracket.  It's in the top right of this image:

---

Suzuki wants lots of Locktite around the stator and rotor:

---

Factories are vary sparse with the words in shop manuals.  Each word is important.  Read it or weep ;-)

---
Of course, there is another possibility.  Maybe I verified the words of an old AMA Pro friend "Never put a fastener on part way."  It is possible that I put the stator screws in finger tight then never made another round for final tightening.

Which ties in nicely with my opening statement about how important it is to be patient while building engines.